We design and manufacture miniature lighting and model railroad products and offer new and used trains and accessories as well as repair, conversion, installation services and training classes.
We specialize in microprocessor based lighting systems, electronics & decoders for model railroaders as well as a full line of G Scale ready to run LGB, PIKO, Hartland Locomotive Works and Starter Sets, Locomotives, Trains, Track, Buildings, Accessories, Power Supplies, Throttles, Sound Systems and DCC Decoders and Systems.
This video shows exterior 1 LED Opal Wall Mount Light fixture mounted on a PIKO cabin (not included)
To replay the video click the replay icon on the bottom left of the screen above or refresh this page.
(building & LED controller not included but available at our store.
Mount the SL-8291230 fixture to illuminate the exterior platforms of cars and parallel
wire to any SL fixture using an SL LED controller or wire direct to an SL LED controller.
Shourt Line SL 8204230 QUAD (4) LED Soft White Opal Light Fixtures for short cars DC/DCC w 2ea mounting Screws and 2ea 18 inch Power Cables for short to medium length G Scale Cars - requires an SL LED controller
The SL-6525911 lighting system provides; LED control/dimmer functions, a UPS circuit with a DC to DC changer and super capacitor bank for powering all 12 LEDs up to 3 minutes without track power, an Aux Out circuit as shown above can be wired to the exterior lamps so they automatically, slowly turn on when the train stops and go off when the train starts. The Automatic circuit has a special feature that smoothly brings the lamps to full brightness regardless of how fast the train stops.
Ready to run; pre-wired - ready to run with an optional SL LED controller
Shourt Line Product Number: No. SL 8210230$49.95Prewired ready to install
The 10 LED lighting set installs in minutes with only a screw driver. (LGB 2080 car shown above not included)
The video above illustrates the full lighting even at low analog track voltage. The SL LED controller also provides the up to 94% efficient lighting, the lowest available for both analog power or DCC power. The 10 LED board runs at less than 20 ma of DCC power or full track power, by far the the lowest in the industry. No other product matches the performance. (train not included with item)
Kit for upgrading the LGB 25604, LGB 26604 Snow Plow Loco with 6 LEDs and Servo Remote Control and Automated Snow Plow Wing Extensions with the ESU 54500 LokSound XL V4.0 Decoder
To replay the video click the replay icon on the bottom left of the screen above or refresh the page. SL-LGB-SPL-Kit Part No.: 9224261 $119.95 (decoder not included - order separately)Available
This kit contains all the parts, wires, LEDs, LED Roof Mounting Board, Servo, Servo Extension, Servo Mount, Linkage, LED Controller and instructions for converting the LGB Snow Plow using the ESU LokSound 4.0 FX decoder (not included) for remote control and automated snow plow wings as well as 6 LEDs using the ESU decoders special lighting effects as shown in the video.
Click here to view the SL-8205363 3mm Candle/Oil lamp Simulation Wall Mounted Fixture
Fixtures require a regulated voltage from 3 to 3.4 volts DC for full output.
LEDs have a simulation circuit built in. Size: .4 x .4 x .74" with peel stick easy mounting. $14.95Available
The SL 8453303's 25 turn output voltage (speed) adjustment allows precise regulated train speed
variations in the input voltage. The output is also short circuit protected with auto reset.
When using the LGB 10345 Automatic Shuttle Kit we recommend using our SL 8453303
Precision Train Throttle (shown below).
The SL 8453303 Precision Train Throttle & LED controller $ 14.95 uses AC,DC or DCC
and has a precision output voltage (speed) control from 1.2 to input
and comes with a full wave
rectifier + 3M mounting pad +10 ft.
black input &
3 inch red/black output cables
The PIKO 35030 Analog Reversing Unit, SL-8552403 Weatherproof throttle & Shourt Line SL-PS-15V1A Power supply shown above provides everything you need for a quick and
solderless installation so you can be auto-reversing your trains in minutes.
Prewired and terminal versions are also available
SL 8453403 Precision Train Throttle & LED controller $ 10.95;
Output 0-30VDC at 3 amps 15 watts Max.
+ screw type terminal wiring blocks
for easy wiring without soldering+ 3M mounting pad
SL 8453203 Precision Train Throttle & LED controller $ 9.95; AC, DC or DCC input
+ full wave rectifier + 3M mounting pad + Prewired 24 in. black input and red/black
cables for motor,
loco, car, layout accessories and lighting
A 16-bit combination microprocessor and digital signal processor is used to produce museum-quality sound that cannot be matched by an 8-bit solution
3 Watts Power
Strong 3 Watt amplifier produces more than sufficient volume for out-of-doors use, capable of handling loads down to 4 ohms.
3-Volt Low-speed Operation
Most sound units do a poor job at low power settings - meaning at low run speeds. Not so with the PB11, it is fully operational at power settings as low as 3 Volts. There is usually some voltage loss from the track through the wheels and contacts to the board, so the track voltage may have to be 5 or 6 volts for continuous operation in order to keep the battery fully charged.
5 triggers for external control
5 different inputs provide flexibility for attaching external controls such as reed switches or remote control trigger outputs.
We are are a Phoenix dealer and offer large scale repair, conversion & installation services world wide. (click here for Phoenix Product Details)